How it works
Will Your Backup System Run the Washing Machine and Dishwasher?
By the WaterQuotes team · Published 2026-11-18 · 6 min read
When the municipal supply drops or cuts out entirely, most homeowners think first about drinking water and flushing toilets. Washing machines and dishwashers tend to come second — until laundry piles up and dishes sit in the sink for two days. The honest answer is that running these appliances from a backup system is entirely possible, but only if the system is designed with their pressure and flow requirements in mind from the start.
Why Appliances Are Fussier Than Taps
A garden tap or bathroom basin is fairly forgiving. If pressure is low, you just wait a little longer for a bucket to fill. Washing machines and dishwashers are different: they have inlet solenoid valves — electrically operated valves that open and close automatically — and those valves require a minimum pressure to open fully. Below that threshold, the machine may stall mid-cycle, trigger a fault code, or simply refuse to fill at all.
Manufacturers specify minimum dynamic pressure (pressure while water is flowing) in their manuals. As a rough guide, most front-loader washing machines require somewhere between 0.5 and 1 bar of dynamic pressure; top-loaders and dishwashers are often in the same range, though some modern machines can manage on the lower end. Check your specific appliance manual — the figure is usually listed under “water supply requirements” or “inlet pressure.” Flow rate matters too: a machine that expects to fill its drum in a set time will run long error-check cycles if the flow is too slow.
What a Gravity-Fed Tank Actually Delivers
A gravity-fed system relies entirely on the height difference between the water surface in the tank and the appliance inlet — this is called the static head. Roughly speaking, every metre of height difference gives you about 0.1 bar of pressure. A tank mounted 2 metres above your washing machine (a common roof-space or elevated-frame installation) therefore delivers around 0.2 bar static pressure, dropping further once water starts flowing.
That is well below what most washing machines need. You can read more about the practical differences in the gravity vs pressurised backup water guide, but the short version is this: gravity feed works well for toilets, basins, and outdoor taps. For washing machines and dishwashers, it usually does not.
If you have already noticed your machine behaving oddly when municipal pressure is low, the low water pressure from tank article walks through the common causes and what can be adjusted.
The Role of a Booster Pump
A pressure pump or pressure-boosting set is what bridges the gap between gravity-fed delivery and what your appliances actually need. These pumps draw water from the storage tank and push it into the household plumbing at a set pressure, typically maintained by a pressure vessel and a pressure switch or controller.
For a standard home with a washing machine, a dishwasher, and normal household fixtures, a pump sized to deliver around 2–3 bar and a flow rate of roughly 20–40 litres per minute is a common starting point — but those figures depend on your pipe sizes, the number of simultaneous draw-off points, and your specific appliances. Get this sized by a qualified installer rather than guessing; undersizing wastes money on a pump that still cannot do the job, and oversizing can damage appliances or create water hammer in your pipes.
The backup water systems section of this site covers system types in more detail, including how tanks, pumps, and controls are typically combined.
If you are not sure whether your existing backup setup can handle your appliances, it is worth getting a professional eye on it. Compare 3 free quotes — vetted installers, no obligation.
Pressure Settings and Pump Controls
Most domestic pressure pumps use a pressure switch set to a cut-in pressure (when the pump starts) and a cut-out pressure (when it stops). A typical domestic setting might be 1.5 bar cut-in and 3 bar cut-out, though your installer should calibrate this to your specific appliances and pipe layout.
A pressure vessel (also called a pressure tank or accumulator) works alongside the pump to smooth out pressure spikes and reduce how often the pump cycles on and off. Without one, every time a solenoid valve opens in the washing machine, the pump kicks on; with a correctly sized vessel, small draw-offs are met from the stored pressurised volume, extending pump life significantly.
If your pump is short-cycling — turning on and off every few seconds — the pressure vessel pre-charge may need adjustment or the vessel may be too small. A plumber or installer can check this quickly.
Plumbing Configuration Matters
Where your backup system feeds into your household plumbing affects which appliances it covers. Some installations connect the backup supply only to specific points (a utility tap, the toilet cisterns) to conserve stored water. If you want the washing machine and dishwasher included, the backup feed needs to reach those supply points, which typically means connecting upstream of those appliances in the cold-water supply line.
Note that most washing machines and dishwashers connect to the cold-water supply only; the appliance heats its own water. This simplifies the plumbing — you only need to ensure cold backup supply reaches the inlet hose connection point at adequate pressure.
If you are also running borehole water through these appliances, the borehole water and appliances article is worth reading. Borehole water chemistry varies and can affect appliance components over time, particularly heating elements and rubber seals, so water quality testing matters before you plumb borehole water into machines.
Water Quality and Your Appliances
Whether your backup source is a rainwater harvest tank, a borehole, or stored municipal water, water quality should not be an afterthought. SANS 241 (2024 edition) is the South African standard for drinking-water quality, and while it technically applies to water intended for human consumption, it is a useful benchmark for water going into appliances as well. Sediment and hardness in particular can damage pump impellers, block inlet filters on washing machines, and fur up dishwasher spray arms.
A sediment pre-filter on the tank outlet is inexpensive and protects both the pump and your appliances. Depending on your water source, a water softener or scale inhibitor may also be worth considering.
Getting the pump sizing, pressure settings, and filtration right from the start saves expensive call-outs later. Get quotes from up to three installers and compare what each recommends for your setup.
What to Confirm Before You Commit
Before finalising a backup water installation — or upgrading an existing one — work through this checklist with your installer:
| Item to confirm | Why it matters |
|---|---|
| Minimum inlet pressure for each appliance | Determines pump cut-in setting |
| Peak simultaneous flow demand | Determines pump flow rate and pipe sizing |
| Tank volume relative to appliance cycle consumption | Avoids running dry mid-wash |
| Pressure vessel sizing | Reduces pump cycling and extends pump life |
| Sediment filtration on tank outlet | Protects pump and appliance inlet valves |
| Connection point in household plumbing | Ensures appliances are actually on the backup circuit |
A washing machine typically uses somewhere between 50 and 100 litres per cycle depending on the programme; a dishwasher broadly similar. If your storage tank is 2,000 litres and you are sharing that with toilet flushing, cooking, and bathing during an extended outage, rationing laundry cycles becomes a practical question, not just a technical one.
The good news is that a properly specified backup system — tank, pump, pressure vessel, and filtration — genuinely does run these appliances as though the municipal supply never dropped. The design decisions made upfront are what determine whether yours will.
Quick answers
What minimum pressure does a washing machine need from a backup water system?
Most front-loader washing machines require a minimum dynamic pressure of around 0.5 to 1 bar at the inlet while water is flowing. Some models will manage on the lower end of that range, but falling below it typically causes the inlet valve to open partially or not at all, resulting in fault codes or incomplete cycles. Always check your specific appliance manual for the manufacturer's stated minimum, and size your pump accordingly.
Can a gravity-fed tank run a washing machine or dishwasher?
In most practical installations, no. A gravity-fed tank delivers roughly 0.1 bar of pressure per metre of height difference between the water surface and the appliance inlet. A tank mounted 2 metres above the machine produces around 0.2 bar static pressure, which drops further once flow begins — well below what most machines require. A pressure pump is the standard solution.
How do I know if my backup pump is set to the right pressure?
Your pump's cut-out pressure should be at or above the minimum inlet pressure required by your most demanding appliance, with a reasonable margin. A common domestic setting is around 1.5 bar cut-in and 2.5–3 bar cut-out, but the right figures depend on your pipe layout and appliances. If machines are faulting or filling slowly, have a qualified installer check and adjust the pressure switch settings and pressure vessel pre-charge.
Does using borehole water in a washing machine cause damage?
It can, depending on the water quality. Borehole water varies significantly in hardness, iron content, and other minerals. Hard water accelerates scale build-up on heating elements and blocks spray arms in dishwashers; high iron content can stain laundry. Having borehole water tested and treating it appropriately — typically with a sediment filter and possibly a softener — before running it through appliances is strongly advisable. The borehole water and appliances article on this site covers this in more detail.
How much water does a washing machine use per cycle from my backup tank?
As a rough guide, a typical front-loader uses somewhere between 50 and 100 litres per cycle depending on the programme selected and the machine's efficiency rating; some modern machines use less. A dishwasher uses broadly similar volumes. When sizing your backup tank, account for all simultaneous household uses — laundry, toilet flushing, cooking, and bathing — to ensure you have enough stored volume to get through an extended outage without running dry mid-cycle.
Sources & notes
Pricing reflects typical Johannesburg market ranges and is confirmed by installer quotation. References: SABS
Ready to compare? Get up to 3 quotes from vetted backup water systems installers in Johannesburg — free, no obligation.
Get 3 free quotes