Installer selection guides

Drilling a Borehole on a New Build: When in the Build to Drill

By the WaterQuotes team · Published 2026-11-18 · 6 min read

Flat illustration of a borehole drilling rig on a new build site beside an unfinished house frame and open trenches

Planning a borehole alongside a new build is one of the smarter decisions a homeowner can make — not because a borehole is a luxury add-on, but because the timing of construction creates a narrow window that makes the whole job cheaper, cleaner and far less disruptive. Miss that window and you are cutting through finished driveways and digging up landscaping you have already paid for.

This guide walks through the logical sequence so you can brief your architect, builder and borehole contractor in one conversation rather than three.

Why timing matters more than you might expect

A borehole drilling rig needs access. That means a clear path wide enough for the rig vehicle and its support truck, firm enough ground to avoid the rig sinking, and no overhead obstacles like newly strung eaves or carport roofs. On a finished property those conditions are rarely all present at once — which is exactly why drilling a rig onto a completed site is often the first problem homeowners underestimate.

On a new build you have a rare period — typically between slab completion and first-fix finishes — when the site is essentially a large, open yard. That is your window.

1. Decide before construction begins, not during. Borehole placement affects where you route electrical supply, where the pressure tank and filtration skid will sit, and potentially where you position utility rooms or garden walls. Those decisions are almost free to make on paper; they become expensive once concrete is poured.

Ask your architect to mark a provisional borehole position on the site plan. Typical minimum clearances from the foundation, septic tanks and sewer lines are set out in municipal by-laws and the Department of Water and Sanitation’s regulations — confirm these with your local authority before fixing the position.

2. Conduct a desktop hydrogeological assessment early. A reputable driller will look at regional geological maps and, ideally, commission a brief geophysical survey before recommending where to drill. Do this before paving or boundary walls go in, so the recommended drilling point is still accessible. If the survey suggests the best fracture zone sits under your planned entertainment area, you want to know that before you lay tiles.

3. Drill after the slab, before paving and boundary walls. This is the sweet spot. The foundation is in place so the rig cannot accidentally undermine it, but nothing else restricts access. The drilling crew can position the rig properly, and the cuttings (the mix of drill water and rock chips that comes up during drilling) can be managed on bare ground rather than on finished surfaces.

For context on what happens when access is tight — including the option of drilling through an existing driveway — the post on drilling through a driveway covers the trade-offs honestly.

4. Run conduits and pipework in the open trenches. This is the single biggest cost saving a new build offers. When electrical trenches for the house are open, adding a conduit run from the borehole position to the DB board costs almost nothing extra in labour. The same applies to the water pipe from the borehole to the point where it enters the house or pressure tank enclosure. On a finished property those trenches have to be cut, dug and reinstated — adding time and cost that is entirely avoidable.

5. Plan the pressure tank and filtration position before internal walls are plastered. A borehole without a pressure tank and some form of water treatment is not a complete system. The tank needs a weatherproof enclosure with drainage and ideally easy access for maintenance. Deciding where this goes after the house is plastered and tiled means retrofitting a utility space; deciding before allows the builder to form it properly.

For a full picture of how the borehole connects to the house plumbing and what that installation involves, the guide on connecting a borehole to your house is worth reading before you finalise the site plan.

If you are still choosing a drilling contractor, getting comparable quotes now — while the site is open — avoids rushed decisions later. Compare 3 free quotes — vetted installers, no obligation.

What if construction has already started?

If you are past the slab and some walls are up but paving has not gone down, you are still in a workable position. The rig access question becomes more important — measure the narrowest gap the rig vehicle needs to pass through and confirm it with your driller before booking.

If paving and boundary walls are already complete, drilling is still possible but the cost and disruption increase. Access limitations, conduit reinstatement and the need to protect finished surfaces all add to the quote. This does not mean you should not proceed — a borehole is a long-term asset — but set realistic expectations about the additional work involved.

Water quality and compliance on a new build

Whether you are on a new build or an established property, borehole water used for potable purposes must be treated and tested to meet SANS 241 (2024 edition), the South African drinking-water quality standard. Build this into your budget and your utility room planning from the start.

Your driller should provide a borehole completion report including the drilled depth, yield test results, and a water sample analysis. File this with your building documentation — you will need it if you ever sell the property or apply for a water use licence through the Department of Water and Sanitation.

Rough cost orientation for new build planning

For planning purposes, complete borehole systems in Johannesburg typically run R40,000–R150,000, with most falling between R60,000 and R100,000. Borehole pumps typically cost R15,000–R35,000 installed. If you are outside Johannesburg, treat these as a reference point only — geology, depth and local labour rates vary considerably — and use quotes from local contractors to build your actual budget.

The saving from drilling during construction (open trenches, easy access, no reinstatement of finished surfaces) is real but difficult to quantify without a site-specific quote. Ask your driller to give you a comparison: cost assuming full open access versus cost if paving were already in. The difference makes the timing argument for itself.

For a full overview of what a borehole system involves — from site assessment through to pump selection and water treatment — the borehole drilling guide covers the complete picture.

The earlier in a build you lock in your driller, the more options you have on placement and service routing. Get quotes from up to three vetted installers — no obligation, and no pressure to commit.

A quick checklist before you brief your contractor

StageAction
Pre-designMark provisional borehole position on site plan; check setback requirements with municipality
Pre-slabCommission geophysical survey if geology is uncertain
Post-slab, pre-pavingDrill borehole; run conduit and pipe in open trenches
Pre-plasterFinalise pressure tank and filtration enclosure position
Pre-occupationWater quality test; borehole completion report filed
OngoingAnnual yield and water quality checks

The sequencing above is straightforward, but it only works if the borehole contractor is booked early enough to fit into the construction programme. Drilling rigs are scheduled weeks in advance, and construction timelines slip. Build a buffer, and have the conversation with your driller before your builder pours the slab — not after.

Quick answers

Can I drill a borehole before the house foundation is laid?

Technically yes, but it introduces risk. If the driller's recommended position conflicts with the final foundation layout, you may end up with a borehole in an awkward spot. The safer sequence is to finalise the foundation position first, then drill once the slab is in place and the site is still open. This way you can confirm the borehole will not sit under a future wall or paved area.

How much space does a drilling rig need to access a new build site?

Requirements vary by rig size, so confirm with your specific contractor. As a general guide, most medium-sized rigs need a clear access path of at least three metres wide and overhead clearance of around four metres or more. New build sites before boundary walls and carports are erected usually meet these requirements easily — which is precisely why drilling early is so much simpler than drilling later.

Do I need council approval to drill a borehole on a new build?

Approval requirements depend on your municipality and the intended water use. Boreholes used for potable supply or above a certain yield threshold may require a water use licence from the Department of Water and Sanitation. Check with your local authority and the DWS before drilling. Incorporating this process into your overall building plan approval timeline is easier than handling it as a separate application afterwards.

What happens to borehole water quality in a new build area where earthworks are still ongoing?

Nearby earthworks, blasting and construction activity can temporarily disturb groundwater and introduce surface contaminants. It is good practice to cap and seal the borehole casing properly immediately after drilling, and to conduct a final water quality test once construction is complete and the site has stabilised before connecting the system for household use. All potable borehole water should meet SANS 241 (2024 edition) standards regardless of when it is tested.

Can I add a borehole to a new build after we have already moved in?

Yes, and many homeowners do. The borehole itself can still be drilled on an established property, though access constraints, driveway reinstatement and the need to cut trenches through finished surfaces all add cost and disruption compared with drilling during construction. It is worth getting a quote that itemises those extra costs so you can make an informed decision rather than comparing like-for-like with a construction-phase price.

Sources & notes

Pricing reflects typical Johannesburg market ranges and is confirmed by installer quotation. References: Department of Water and Sanitation

Ready to compare? Get up to 3 quotes from vetted borehole drilling installers in Johannesburg — free, no obligation.

Get 3 free quotes

Stop hoping the taps work.

Get your 3 free quotes today.

Get 3 free quotes