Regulations & registration

Borehole Water Meters and Abstraction Records for Businesses

By the WaterQuotes team · Published 2026-10-28 · 5 min read

Flat illustration of a commercial borehole with an inline water meter on the rising main and a logbook beside it

Knowing how much groundwater your business draws is not just good housekeeping — for many operations it is a legal expectation under the National Water Act. Yet metering and record-keeping remain the part of borehole compliance that businesses most often overlook, sometimes discovering the gap only when a DWS inspector arrives or a registration renewal is due. This article explains where a meter goes, what readings to keep, and how abstraction records connect to your broader compliance obligations.

Why abstraction records matter for businesses

South Africa’s groundwater is a public resource managed under the National Water Act (Act 36 of 1998). The Act requires users to keep records that allow the Department of Water and Sanitation (DWS) to monitor how much is being taken from an aquifer. For businesses, this matters for several reasons.

First, your borehole registration or licence will almost always specify a maximum annual or monthly volume. Without a meter you have no way to demonstrate — or even know — whether you are within that limit. Second, if DWS ever audits your site, written abstraction records are the primary evidence that you are using water lawfully. Third, in water-scarce catchments, exceeding an allocation can trigger enforcement action or affect future licence renewals. Understanding what commercial borehole registration involves is the starting point, but the metering obligation lives with you long after registration is approved.

Where a borehole water meter is installed

The standard position for a borehole water meter is on the rising main — the pipe that carries water from the pump up to your storage tank or reticulation system — as close to the wellhead as is practical. Installing it here, before any branching or bypass, ensures every litre drawn from the aquifer is captured.

Key installation points:

  • Meter type: A mechanical inline pulse meter or a mag-flow meter are both commonly used. Mag-flow meters suit boreholes that deliver water with fine sediment because there are no moving parts to wear. Your installer can advise which suits your pump and flow rate.
  • Orientation: Most meters have an arrow indicating flow direction; fitting it the wrong way around gives false readings or damages the mechanism.
  • Bypass prevention: Where a bypass loop exists for maintenance, make sure the meter cannot be circumvented during normal operation. DWS guidance expects all abstraction to pass through the meter.
  • Protection: Mount the meter in a lockable meter box or housing to protect it from UV, frost in higher-altitude areas, and tampering.

If your system was installed without a meter, a competent pump technician can retrofit one during a scheduled service visit. Commercial borehole servicing is a sensible time to address this.

Reading frequency and logbook format

There is no single nationally prescribed logbook format, but DWS expects records that are consistent, dated, and legible. A practical minimum for most businesses is a monthly reading, taken on the same date each month and recorded immediately. Many operations that run multiple shifts or pump continuously find weekly readings give better visibility of unusual consumption spikes.

A straightforward logbook entry should capture:

FieldExample
Date of reading2025-06-30
Meter serial numberMFM-00423
Cumulative meter reading (m³)4 821
Volume this period (m³)147
Reader’s name / signatureT. Mokoena
NotesPump serviced 2025-06-15

Keep both a physical logbook on site and a digital copy — a simple spreadsheet works. If a meter is replaced or recalibrated, note the old and new meter readings on that date so there is no gap in the cumulative record. DWS recommends retaining abstraction records for at least five years; check your registration conditions, as some licences specify longer retention periods.

If your business hasn't yet registered its borehole or you're unsure whether your current setup meets the metering requirements, getting professional input early saves time later. Compare 3 free quotes from vetted installers who understand the compliance picture — no obligation.

Connecting meter records to DWS reporting

Registration and licensing under the National Water Act can include a reporting obligation. The process of registering a borehole with DWS typically results in registration conditions that specify whether you must submit abstraction data, and how often. For many smaller general-use registrations the condition is simply to keep records available for inspection. Larger volume users or those in sensitive catchments may have active reporting requirements — quarterly or annual returns submitted to the relevant DWS regional office.

If you are unsure what your registration conditions say, the safest step is to contact your DWS regional office directly with your water use authorisation reference number and ask for clarification in writing. Do not rely on what a previous owner or contractor told you; get it confirmed from the source.

Meter accuracy and calibration

A meter that under-reads may make you appear compliant when you are not. A meter that over-reads can make you look like you are breaching an allocation. Neither outcome is helpful.

As a rough guide, most mechanical pulse meters are factory-calibrated and accurate to within a few percent when new, but high-sediment water or long service periods can degrade accuracy. Consider having your meter checked or replaced every three to five years, or sooner if you notice readings that do not match expected consumption patterns. Ask your service technician to document the check in your logbook.

Water quality also matters here. SANS 241 (2024 edition) is the South African standard for drinking-water quality, and if your borehole water enters any part of your premises that staff or customers may drink, testing against SANS 241 is the responsible baseline. A metre reading tells you how much you are drawing; a water test tells you whether what you are drawing is safe for its intended use. Test first, then determine treatment needs — the two questions are related but separate.

Getting the metering and records right from the start is far simpler than retrofitting compliance later. Request free quotes from experienced commercial borehole contractors who can advise on meter placement, calibration, and logbook requirements for your specific setup.

Practical steps to get compliant now

If your business is already drawing from a borehole but has not formalised its metering or records, here is a sensible sequence:

  1. Locate your water use authorisation documents. Confirm whether your borehole is registered, and what the registration conditions require.
  2. Inspect the current setup. Is a meter fitted? Where? Is it readable and functioning?
  3. Retrofit or replace if needed. Arrange a service visit to fit or check the meter.
  4. Start the logbook from today. You cannot reconstruct accurate historical data, but a clean record from a known start date is far better than nothing.
  5. Confirm reporting obligations with your DWS regional office in writing.
  6. Schedule annual service and meter checks so the system stays in reliable order.

Borehole metering is one of those compliance tasks that looks burdensome upfront but becomes routine quickly once a simple log is in place. The bigger risk is not having records when they are needed.

Quick answers

Is a borehole water meter legally required for businesses in South Africa?

The National Water Act and the conditions attached to your water use authorisation or registration typically require that abstraction can be measured and recorded. In practice, this means fitting a meter is expected for most commercial users. The specific obligation depends on your registration conditions, so check your authorisation document or contact your DWS regional office to confirm what applies to your site.

What type of water meter is best for a commercial borehole?

Both mechanical inline pulse meters and mag-flow (electromagnetic) meters are used on commercial boreholes. Mag-flow meters are generally preferred where the water contains fine sediment or minerals that can wear moving parts, since they have no internal mechanisms to degrade. The right choice depends on your pump's flow rate and the water quality at your site — a qualified pump technician or borehole contractor can recommend the appropriate specification.

How long must I keep borehole abstraction records?

DWS generally recommends retaining abstraction records for at least five years, but your specific registration or licence conditions may specify a different period. Always check your water use authorisation document for the exact requirement. Keeping both a physical logbook on site and a digital backup is good practice regardless of the minimum period.

What happens if my borehole meter breaks or gives inaccurate readings?

If you suspect a meter is faulty, document the issue in your logbook immediately — note the date, the last reliable reading, and what you observed. Arrange for a service technician to inspect or replace the meter as soon as possible and record the old and new meter readings at the time of replacement. A brief, documented gap caused by a known fault is far more defensible with DWS than an unexplained absence of records.

Do I need to report my abstraction volumes to DWS, or just keep records on site?

It depends on your water use authorisation. Many registrations only require you to keep records available for inspection, while licences for larger-volume or sensitive-catchment users may include active reporting obligations such as quarterly or annual returns. Contact your DWS regional office with your authorisation reference number to confirm your specific obligations in writing — do not assume the position is the same as a neighbouring business.

Sources & notes

Pricing reflects typical Johannesburg market ranges and is confirmed by installer quotation. References: Department of Water and Sanitation · SABS

Ready to compare? Get up to 3 quotes from vetted commercial water solutions installers in Johannesburg — free, no obligation.

Get 3 free quotes

Stop hoping the taps work.

Get your 3 free quotes today.

Get 3 free quotes