How it works

Do You Need a Pressure Vessel with a Tank Pump? Sizes and Set-Up

By the WaterQuotes team · Published 2026-10-30 · 5 min read

Flat illustration of a tank pump connected to a pressure vessel with pressure switch, showing water flow to a house

A pressure vessel is one of those components that homeowners rarely think about until the pump starts clicking on and off every few seconds — that rapid cycling that hints at trouble. If you have a tank-and-pump backup system or a borehole setup, understanding whether you need a pressure vessel, what size suits your home and how the whole arrangement fits together will save you money and frustration.

What a pressure vessel actually does

A pressure vessel (sometimes called an accumulator tank or bladder tank) is a sealed steel or fibreglass cylinder with a rubber bladder inside. One side of the bladder holds compressed air pre-charged to a set pressure; the other side holds water supplied by the pump.

When the pump runs, it pushes water into the vessel and compresses the air. When you open a tap, the pressurised water is pushed out by that air cushion — without the pump needing to start. Only when the vessel is largely depleted does the pressure drop enough to trigger the pressure switch and bring the pump back on.

The result: instead of the pump firing up every time someone opens a tap to fill a glass, it runs in longer, less frequent cycles. That matters because electric motors draw the highest current at start-up, and every unnecessary start adds heat, wear and electricity cost.

When you definitely need one

Not every pump setup requires a pressure vessel, but most do. Here are the clearest cases:

  • Any pump controlled by a pressure switch. A pressure switch cuts the pump in and out at set pressures (typically around 2 bar cut-in, 4 bar cut-off, though settings vary). Without a vessel to hold pressure between switch points, the pump will cycle almost continuously under light demand.
  • Variable-speed (inverter) pumps. Some modern variable-speed pumps tolerate short-cycling better, but a small pressure vessel still provides a buffer and is usually recommended by manufacturers.
  • Borehole and tank-fed systems. If you have a backup water tank feeding a pressure pump — the kind of setup explored across our backup water systems guide — a pressure vessel is almost always part of a proper installation.
  • High-demand households. More people, more simultaneous draw-offs, more start cycles without a vessel.

The one common exception is a pump driving a gravity-fed header tank above the house, where no pressure switch is involved and the tank itself acts as the buffer.

Choosing the right size

Vessel size is often misunderstood. A larger vessel does not give you higher pressure — that is set by the pump and the pressure switch. What a larger vessel gives you is a bigger drawdown volume: the amount of water delivered between pump start-up and the next start-up. More drawdown means longer, fewer pump cycles.

As a rough guide for South African homes:

Household sizeSuggested vessel capacity
1–2 people, light use8–19 litres
2–4 people, typical home20–35 litres
4–6 people or multiple bathrooms35–50 litres
Large home, smallholding50–100 litres or more

These are starting-point ranges — confirm sizing with an installer who can assess your pump’s flow rate and your household’s peak demand. The vessel must also be rated for pressures at least as high as your system’s maximum cut-off pressure.

For a deeper look at how the pressure switch interacts with your tank and pump, the post on borehole pressure switch and tank setup walks through the logic in detail.

How the system is set up

A typical tank-pump-vessel arrangement works like this:

  1. Storage tank (JoJo or similar) collects municipal water, rainwater or borehole water.
  2. Pump draws from the tank and pushes water into the household supply line.
  3. Pressure vessel sits on the pressure side of the pump, usually close to it, connected via a tee fitting.
  4. Pressure switch reads line pressure and signals the pump controller to start or stop.
  5. Non-return (check) valve sits between the pump and the vessel to prevent back-flow when the pump stops.

The vessel is typically installed upright or at the angle the manufacturer specifies, close to the pump to minimise pressure losses. It needs to be accessible because the air pre-charge must be checked periodically — usually once or twice a year — with a standard tyre-pressure gauge. The pre-charge pressure should be set to about 0.2 bar below the pump’s cut-in pressure when the vessel is empty of water.

If you're putting together a tank-and-pump system and want to know what local installers charge, compare 3 free quotes — vetted installers, no obligation.

Pre-charge pressure: the detail most people miss

A vessel with an incorrect pre-charge is almost as problematic as having no vessel at all. If the pre-charge is too high, the bladder never fills properly and you lose most of the drawdown volume. If it is too low, the bladder bottoms out and the vessel effectively stops working.

Always check the pre-charge with the vessel isolated from system pressure (pump off, water pressure bled down). Top up with a standard foot pump or compressor if needed. This is a simple maintenance task that dramatically extends both the vessel’s life and the pump’s.

What a pressure vessel system typically costs

The vessel itself is a relatively small part of a backup water installation. Pressure vessels for residential use typically range from around R1,500 for a small 8-litre unit to R5,000 or more for a 50-litre unit — but treat those as rough reference points and get quotes, because fittings, installation labour and the pump itself all add to the total.

For context on the broader cost picture, the article on backup water pump costs covers what you can expect to pay for different pump types and complete system setups. For Johannesburg specifically, backup tank-and-pump systems typically run R20,000–R40,000, with whole-house examples around R55,000, though those figures are Johannesburg reference points and will vary elsewhere.

A well-sized pressure vessel is worth little without the right pump behind it — get installer quotes for your full system and compare what's included before committing.

Maintenance and when to replace

A quality pressure vessel installed correctly and maintained properly can last ten to fifteen years, though bladder failure can occur earlier if the pre-charge is neglected or if water quality is poor. Signs that the vessel or bladder has failed include:

  • The pump cycles rapidly even under very light draw (a tap barely open).
  • Water comes out of the Schrader valve (air charging point) when you depress the pin — that means the bladder has burst.
  • Pressure fluctuates wildly at the tap.

Replacing a failed vessel promptly protects the pump from the accelerated wear of short-cycling. It is a straightforward job for any plumber or pump installer.

Ultimately, a pressure vessel is not an optional extra for most tank-pump setups — it is a core component that makes the system work properly. Get the size right, set the pre-charge correctly, and check it annually, and this modest piece of equipment will quietly protect one of the more expensive items in your backup water system.

Quick answers

Can I run a pressure pump without a pressure vessel?

Technically yes, but the pump will short-cycle — starting and stopping constantly — under any light demand. This accelerates motor wear, increases electricity consumption and can trip thermal overload protectors. For any pump controlled by a pressure switch, a pressure vessel is strongly recommended and included as standard in any properly designed installation.

What pre-charge pressure should I set in my pressure vessel?

As a general rule, set the air pre-charge to approximately 0.2 bar below the pump's cut-in pressure, measured with the vessel isolated from system pressure and all water bled out. For example, if your pressure switch cuts in at 2 bar, pre-charge to roughly 1.8 bar. Always check the manufacturer's specification for your particular vessel and pump combination.

How often does a pressure vessel need maintenance?

Check the air pre-charge at least once a year using a standard tyre-pressure gauge at the Schrader valve, with the system depressurised first. Also inspect the vessel body for corrosion or damage annually. Most quality vessels require no other routine maintenance beyond keeping the pre-charge correct.

Will a bigger pressure vessel give me better water pressure?

No — water pressure is determined by your pump's output and the pressure switch settings, not the vessel size. A larger vessel increases the drawdown volume, meaning more water is delivered between pump cycles, resulting in fewer, longer pump runs. This reduces wear but does not raise the pressure at your taps.

How do I know if my pressure vessel bladder has failed?

The clearest sign is rapid pump cycling even when barely any water is being used. You can also depress the pin inside the Schrader (air charge) valve with the system pressurised — if water sprays out instead of air, the bladder has burst and the vessel needs replacing. A failed bladder means the vessel provides no buffer at all.

Sources & notes

Pricing reflects typical Johannesburg market ranges and is confirmed by installer quotation. References: SABS

Ready to compare? Get up to 3 quotes from vetted backup water systems installers in Johannesburg — free, no obligation.

Get 3 free quotes

Stop hoping the taps work.

Get your 3 free quotes today.

Get 3 free quotes