How it works

Backup System Not Switching to the Tank? Common Switchover Faults

By the WaterQuotes team · Published 2026-11-03 · 7 min read

Flat illustration showing a home backup water system with a tank, solenoid valve, pressure switch and pipe layout

Mains pressure drops and your backup system should take over seamlessly. When it does not, the experience is jarring — no warning, no water, no obvious reason. Before you call an installer in a panic, it helps to understand what a switchover actually involves and where it typically breaks down.

A complete backup water system has several moving parts that must all cooperate: a storage tank with sufficient water, a sensor or float to detect that mains supply has dropped, a switching mechanism (usually a solenoid valve or a purpose-built transfer valve), a pump to deliver adequate pressure, and the electrical supply to run all of it. Failure at any single point stops the chain. The backup water systems guide covers how these components fit together; this article focuses on what goes wrong with the switchover specifically.

The Solenoid Valve Is Stuck or Unpowered

The solenoid valve is the most common single point of failure in a backup switchover. In a typical installation, one solenoid valve is held open by mains pressure or electrical signal during normal supply, and a second (or the same valve in reverse) opens to allow tank water through when mains drops. If the valve coil burns out, the valve body corrodes internally, or the electrical feed to it is interrupted, it stays in whichever position it was last in.

A valve stuck in the mains-open position will block tank water from entering your pipes even when the pump is running. A valve stuck in the tank-open position wastes stored water continuously into the mains when supply returns. Neither failure is loud or dramatic — you simply get no water or unexpectedly high tank consumption.

Check: Is the solenoid valve receiving power? A multimeter across the coil terminals will show whether 220 V (or whatever control voltage the system uses) is arriving. If power is present but the valve does not click or hum, the coil is likely dead. Replacement coils are usually available without replacing the entire valve body, which keeps costs down.

A Pressure Switch or Float Sensor Has Failed

The switchover is triggered by something detecting that mains pressure has fallen. Older systems use a simple pressure switch — a mechanical device that closes a circuit when line pressure drops below a set threshold. Newer systems may use electronic pressure transducers or float switches in a break-tank.

Pressure switches fail in two ways: they can stick open (never triggering the switchover) or stick closed (triggering it even when mains supply is fine, draining your tank unnecessarily). Float switches in tanks can corrode, tangle on the tank wall, or simply fill with water and sink, giving a false reading.

Check: If your system has a manual override or test button, use it — if the pump starts and tank water flows, the mechanical switchover path is intact and the sensor is the problem. If there is no override, a qualified installer can temporarily bridge the sensor circuit to confirm the diagnosis.

Isolation Valves Left in the Wrong Position

This is embarrassingly common and easy to miss. Backup systems typically have several isolation valves — on the tank outlet, on the pump inlet, and on the bypass line. During a service, repair, or plumbing work elsewhere in the house, one of these valves may be closed and not reopened. The pump runs, pressure looks fine on the controller, but water cannot physically reach your taps.

The municipal-to-tank switchover process explains the valve sequence in detail, and it is worth reading before doing any DIY inspection. A visual walk of your pipework looking for any valve handle sitting perpendicular (closed) to the pipe rather than parallel (open) takes five minutes and costs nothing.

The Tank Is Empty or Below the Pump’s Minimum Level

A backup system cannot switch over to water that is not there. Tanks deplete faster than most homeowners expect, particularly during extended outages when habits do not change. Some pump controllers have a low-level cutout to protect the pump from running dry; when the tank drops below that float level, the pump stops and the switchover appears to fail.

Some systems have no low-level protection at all, in which case the pump runs dry, overheats, and may cut out on thermal protection — presenting the same symptom.

Check the physical water level in the tank directly if you can. If it is low, the system is working as designed — it simply has nothing to deliver. Understanding how a well-sized system keeps water running through an outage can help you size storage correctly so this does not recur.

If diagnosing your own system reveals a component that needs replacing or a setup that was never quite right, it may be time to get a proper assessment. Compare 3 free installer quotes — vetted professionals, no obligation.

Pump Faults That Mimic Switchover Failure

Occasionally the switchover itself works correctly — the valve opens, the sensor fires, the controller switches — but the pump fails to build pressure, so the outcome looks identical: dry taps. Common pump faults include a seized impeller, a failed capacitor on single-phase motors, a tripped breaker, or a pump that has lost its prime after running dry previously.

If you can hear the pump motor humming but no water is moving, a seized impeller or lost prime is likely. If the motor is completely silent, check the dedicated breaker and the pump’s own overload reset button (usually a small red button on the motor body). A pump that trips its overload repeatedly is telling you something is wrong mechanically or thermally — do not keep resetting it without investigating.

Controller and Wiring Issues

Modern backup systems often include an electronic controller that manages the switchover logic, pump speed (on variable-speed systems), and fault alerts. Controllers can develop firmware glitches, corroded terminals, or failed relays. A controller that believes mains is still live — because its sensor input is stuck — will never trigger the switchover regardless of actual supply conditions.

Check for any fault codes or LED indicators on the controller face. Most manufacturers publish fault code tables in the installation manual; if you do not have it, the model number on the controller face usually leads to a PDF online. Knowing the fault code before you call an installer saves diagnostic time and therefore money.

Good after-sales support from your original installer should mean you can call and describe the fault code and get guidance. If your installer is unresponsive, the after-sales service expectations article outlines what you are entitled to ask for.

When to Stop DIY and Call a Professional

Voltage checks on solenoid coils, valve position inspections, and tank level checks are all safe for a competent homeowner. Anything involving rewiring the controller, replacing the solenoid valve body on a pressurised line, or working on the pump while it is energised crosses into territory that requires a qualified plumber or electrician, depending on the work.

South African drinking-water installations must meet SANS 241 (2024 edition) requirements at the point of use, and any plumbing work that connects to potable water should be done by a registered professional to ensure compliance and to protect your insurance position.

A fault that keeps recurring despite your own checks usually points to an installation problem rather than a single failed part. Get quotes from up to three vetted installers and have someone assess the system properly.

A Quick Fault-Finding Reference

SymptomMost Likely CauseFirst Check
No water, pump silentTripped breaker or pump overloadBreaker panel, then pump reset button
No water, pump running and hummingSeized impeller or lost primeListen for water movement; check prime port
No water, pump not starting at allSensor not triggering switchoverSensor wiring and signal voltage
No water, controller shows mains OKSensor stuck or faultyManual override test
Water runs briefly then stopsTank near empty or low-level cutout activePhysical tank level check
Tank depletes with no outageSolenoid valve stuck open to tankValve coil voltage check

A systematic approach — working from the tank inward toward the taps — usually identifies the fault within 20–30 minutes. Most component failures are individually inexpensive to fix; the cost escalates when a fault goes undiagnosed and causes secondary damage, such as a pump that burns out from running dry repeatedly.

Quick answers

Why does my backup system work during a test but not during an actual outage?

Test procedures often involve manually triggering the pump or opening a valve by hand, bypassing the automatic sensor circuit entirely. During a real outage, the sensor or pressure switch must detect the drop and fire the switchover signal on its own. If that sensor is intermittent or has a slow response, it may miss a brief or gradual pressure drop but respond fine to a manual test.

Can a power outage cause a backup water system to stop switching over?

Yes, if the switchover relies on electrically operated solenoid valves or an electronic controller, a simultaneous power and water outage will disable the switching mechanism. Some systems are designed with a gravity-fed or normally-open valve arrangement specifically to handle this scenario. If your area experiences both power and water outages together, ask your installer whether your system is configured to handle that combination.

How often should the switchover mechanism be tested?

As a rough guide, testing the automatic switchover every three to six months is a sensible minimum. This means simulating a mains failure (usually by closing the mains isolation valve briefly) and confirming that tank water flows within a few seconds. Regular testing also catches a depleted tank before you need it, which is one of the most avoidable switchover failures.

Is a stuck solenoid valve dangerous?

A solenoid valve stuck in the wrong position is not immediately dangerous, but it can cause significant problems. A valve stuck open to the tank can silently drain your stored water into the mains return line, leaving you with nothing during the next outage. It should be repaired rather than ignored, but it is not an emergency that requires shutting off the entire water supply unless water is physically leaking from the valve body.

Will my home insurance cover a switchover fault that causes water damage?

This depends entirely on your policy wording and insurer. Most insurers want plumbing work to have been done by a registered plumber; a DIY installation that fails and causes damage to property could be excluded. Keep installation invoices and any certificates of compliance issued by your installer, as these are typically the documents an insurer will request when assessing a claim.

Sources & notes

Pricing reflects typical Johannesburg market ranges and is confirmed by installer quotation. References: SABS

Ready to compare? Get up to 3 quotes from vetted backup water systems installers in Johannesburg — free, no obligation.

Get 3 free quotes

Stop hoping the taps work.

Get your 3 free quotes today.

Get 3 free quotes