How it works
Types of Pressure Pumps for Home Tank Systems Compared
By the WaterQuotes team · Published 2026-11-06 · 7 min read
If your home runs on a backup tank — whether fed by a borehole, rainwater harvesting, or municipal top-up — you almost certainly need a pressure pump to push water through your taps, showers, and appliances at a usable pressure. The confusing part is that there are several quite different pump types on the market, and installers do not always explain what distinguishes them or why one matters over another.
This guide lays out the five types you will most commonly encounter, what each one does well, and where it falls short. It sits alongside the broader backup water systems guide if you want context on the full system before drilling into the pump decision.
Why pump type matters more than brand
A pump is not just a motor that moves water. The internal mechanism determines how the pump creates pressure, how efficiently it does so, what happens when demand fluctuates, and how long it lasts under typical South African conditions — including load-shedding cycles that cause repeated hard starts. Getting the wrong type for your situation leads to either weak pressure, premature failure, or unnecessarily high electricity bills. Brand is secondary to getting the mechanism right.
Peripheral pumps
Peripheral pumps (sometimes called regenerative or side-channel pumps) are the small, low-cost units you will see in most hardware stores. They use a spinning impeller with small vanes around its edge to build pressure gradually through a spiral chamber.
Strengths: Inexpensive, compact, widely available, simple to service. They handle low-to-moderate flow requirements well and are adequate for a single-storey home with modest demand — perhaps one or two bathrooms used in turn rather than simultaneously.
Trade-offs: They do not like pumping sandy or silty water, cavitate easily if the inlet runs dry even briefly, and struggle to maintain pressure when multiple outlets open at once. They also tend to run noisily at higher loads. For homes with more than three or four simultaneous draw points, they are usually undersized.
Jet pumps
Jet pumps use a venturi effect — fast-moving water through a narrow jet creates suction — to draw water from a tank or shallow source and boost it into the pressure line. Shallow-well jet pumps work with the jet assembly above ground; deep-well versions lower part of the assembly closer to the water source.
Strengths: Reasonably priced, self-priming, and capable of lifting water from moderate depths without submerging the motor. Useful when the tank sits below the pump or when the installation needs the motor accessible for easy maintenance.
Trade-offs: They are less efficient than centrifugal designs because the venturi wastes some energy. They are also sensitive to air leaks in the suction line, which causes loss of prime and intermittent pressure. In a rainwater or tank-fed setup where the tank is above the pump, a jet pump is often overkill — a simpler peripheral or multistage unit will do the job more efficiently.
Multistage centrifugal pumps
A multistage centrifugal pump stacks multiple impeller stages in series. Each stage adds pressure, so by the time water exits the final stage it carries considerably more head than a single-stage unit of similar size could produce. These are the workhorses of medium-to-large home backup systems.
Strengths: Efficient across a wide flow range, capable of delivering high pressure to multi-storey homes or properties with long pipe runs, relatively quiet, and tolerant of continuous duty cycles. They handle the repeated start-stop cycles caused by load-shedding better than peripheral pumps because they are built to tighter tolerances. For anyone running a whole-house backup system — the kind that sits in the R20,000–R55,000 range for tank and pump combined — a multistage unit is usually what a competent installer will recommend.
Trade-offs: More expensive upfront than peripheral or jet pumps. They also need clean water; fine sediment from an unfiltered rainwater tank or an uncased borehole will wear the impeller stages faster than the rated service life. Pre-filtration is not optional with this pump type.
For a fuller look at what installed pump costs look like, the backup water pump costs breakdown is worth reading before you request quotes.
Submersible pumps
Submersible pumps are sealed units designed to operate fully submerged — either inside an underground borehole casing or sitting at the bottom of a large storage tank. The motor and pump are integrated into one waterproof assembly that relies on the surrounding water for cooling.
Strengths: Because the pump is already below the water surface, it never needs to lift water against suction — it pushes from below, which is mechanically more efficient for deep sources. Submersibles are the standard choice for boreholes for this reason. They are also silent at surface level since the motor is underground or submerged.
Trade-offs: Access for maintenance requires pulling the entire unit out of the borehole or tank, which means professional labour each time. Motor failures caused by running dry (if the borehole yield drops or the tank empties) can be expensive to repair or replace. A dry-run protection controller is essential. As a Johannesburg reference point, borehole pump installations including the pump, casing, controller, and wiring typically run R15,000–R35,000.
If you are deciding whether your tank setup even needs a pump — or whether gravity feed might suffice — the do you need a pump for your water tank article walks through that decision.
If you are weighing up pump types and want to see what installers in your area actually quote for your specific setup, compare 3 free quotes — vetted installers, no obligation.
Variable-speed (inverter-driven) pumps
Variable-speed pumps use an inverter drive to adjust motor speed in real time based on demand. Instead of running at full power whenever the pressure switch triggers, the motor ramps up or down to match exactly what the household is drawing at that moment.
Strengths: Significantly lower electricity consumption compared with fixed-speed equivalents, particularly in households where demand varies a great deal across the day. They deliver noticeably steadier pressure — no surge when the pump kicks in and no dip when two taps open at once. For anyone who has experienced the pressure swings common with standard on/off systems, this is a meaningful quality-of-life improvement. The constant pressure vs standard pumps comparison explains the technical difference in more detail.
Trade-offs: Higher purchase price, and the inverter electronics add a component that can fail — particularly if exposed to lightning surges or significant voltage instability, both of which are real concerns in South Africa. A quality surge protector is not optional. Repairs can be more expensive than fixing a straightforward fixed-speed motor.
Side-by-side comparison
| Pump type | Relative cost | Best suited for | Main weakness |
|---|---|---|---|
| Peripheral | Low | Small homes, 1–2 bathrooms, clean water | Multiple simultaneous outlets, sandy water |
| Jet | Low–medium | Moderate lift, accessible motor preferred | Efficiency loss, air-leak sensitivity |
| Multistage centrifugal | Medium | Multi-storey homes, whole-house systems | Needs clean, filtered water |
| Submersible | Medium–high | Boreholes, deep tanks | Maintenance access, dry-run risk |
| Variable-speed | High | High demand, electricity efficiency priority | Electronics, surge vulnerability |
Prices vary by brand, installer, and region. Use the table for relative positioning only, not as a quote substitute.
What the pump must comply with
All electrical pump installations in South Africa must comply with SANS 10142 (the wiring code), and any equipment used in a potable water line must not introduce contaminants contrary to SANS 241 (2024 edition), the national drinking-water quality standard. When getting quotes, it is reasonable to ask installers to confirm that the equipment they supply meets applicable SANS requirements. A reputable installer will not hesitate to answer.
Ready to move from comparison to actual numbers for your home? Get 3 installer quotes free — no commitment, just real prices for your situation.
Choosing between them
The honest answer is that most homeowners should not choose a pump type in isolation — they should describe their situation to two or three installers and let the pump recommendation follow from the system design. The variables that drive the decision are: tank position relative to the house (height difference), number of bathrooms and simultaneous users, whether the source is a borehole or surface tank, water quality, and how much load-shedding disruption the household can tolerate.
What this guide gives you is enough vocabulary to have an informed conversation with those installers, spot a recommendation that does not match your situation, and ask the right follow-up questions. That is usually worth more than arriving at a quote with a pump model already decided.
Quick answers
What is the most common pressure pump type for a home backup tank system?
Multistage centrifugal pumps are most commonly specified for whole-house backup tank systems because they balance pressure performance, efficiency, and durability across a range of flow rates. Peripheral pumps are common in smaller, simpler setups where cost is the primary concern. The right choice depends on your home's size and water demand.
Can I use a submersible pump with an above-ground storage tank?
Yes, submersible pumps can be installed inside large above-ground or underground tanks, not only in boreholes. They work well when the tank is large enough to keep the pump submerged under normal use conditions. The key requirement is a dry-run protection controller to cut power if the water level drops too low, since running dry quickly damages the motor.
Are variable-speed pumps worth the extra cost in South Africa given load-shedding?
Variable-speed pumps do save electricity under normal use, but the inverter electronics are more vulnerable to voltage spikes and surges that accompany load-shedding if the system is not properly protected. A quality surge protector and possibly an uninterruptible power supply add to the upfront cost. Whether the electricity saving justifies the total outlay depends on how often the pump runs and your electricity tariff — an installer can model this for your specific situation.
What water quality do I need before installing a multistage centrifugal pump?
Multistage centrifugal pumps require clean, filtered water because sediment and grit wear the close-tolerance impeller stages faster than the rated service life. If your source is rainwater or an uncased borehole, pre-filtration — typically a sediment filter upstream of the pump — is essential. SANS 241 (2024) sets the national standard for potable water quality, and your installer should advise on appropriate pre-treatment for your source water.
How do I know whether a peripheral pump is powerful enough for my home?
A rough guide is to count the number of outlets likely to be open at the same time — showers, taps, and appliances. If that number is three or more running simultaneously, most peripheral pumps will struggle to maintain adequate pressure. Single-storey homes with one or two bathrooms used in turn are where peripheral pumps genuinely perform; anything beyond that usually justifies a multistage or variable-speed unit. Confirm flow and pressure requirements with an installer before purchasing.
Sources & notes
Pricing reflects typical Johannesburg market ranges and is confirmed by installer quotation. References: SABS
Ready to compare? Get up to 3 quotes from vetted backup water systems installers in Johannesburg — free, no obligation.
Get 3 free quotes