How it works

Upgrading an Existing Backup System: Adding a Pump, Tank or Switchover

By the WaterQuotes team · Published 2026-11-07 · 6 min read

Flat illustration showing a home water backup system being upgraded step by step, from a basic tank to a pressurised automatic switchover system

A basic JoJo tank and a ball valve get you through a short outage, but they rarely deliver the pressure or convenience most households expect. The good news is that a backup system is not an all-or-nothing purchase — you can build on what you already have, one upgrade at a time, spreading the cost and only buying what your situation actually needs.

This guide walks through the most common upgrade paths, what an installer looks for before adding on, and how to avoid buying equipment that does not suit your existing setup.

Why upgrading in stages makes sense

Most South African homeowners start with a tank because it is the cheapest and quickest entry point. It buffers against outages but leaves you hauling water by bucket or relying on gravity trickle flow through a header-tank connection. Each upgrade layer — a pump, an automatic switchover, a second tank — adds reliability and convenience without replacing what already works.

The alternative, buying a fully integrated system upfront, makes sense if you are starting from zero. But if a tank is already in place and functioning, retrofitting is almost always cheaper than starting again. For a broader look at what a complete system involves, the backup water systems overview is worth reading before you commit to any upgrade path.

What an installer checks before adding anything

Before quoting an upgrade, any competent installer should assess four things:

  1. Tank position and height. A tank on the ground cannot gravity-feed anything above it. If yours is ground-mounted, a pump is non-negotiable for indoor use.
  2. Pipe diameter and condition. Undersized or corroded pipes choke pump performance regardless of how powerful the motor is.
  3. Electrical supply near the tank. A pressure pump needs a dedicated circuit or at least a weatherproof outlet close by. Running a long extension cable is not a safe or lasting solution.
  4. Inlet arrangement. How the tank fills — from the municipal line, rainwater, or a borehole — determines whether a switchover valve or float valve upgrade is straightforward or requires replumbing.

Skipping this assessment is how homeowners end up with a pump that cavitates, a switchover that leaks, or a second tank that fills from the wrong source.

Upgrade 1: Adding a pressure pump to a gravity-fed tank

This is the most common and most impactful single upgrade. A gravity-fed tank mounted at ground level delivers very low pressure — typically not enough for a shower, a washing machine, or most dishwashers. A pressure pump (also called a booster pump or transfer pump) draws water from the tank and delivers it at a pressure comparable to municipal supply.

What to look for:

  • Auto-start pressure switch. The pump should start automatically when a tap opens and stop when it closes. Manual-start pumps are cheaper but impractical for everyday use.
  • Pressure tank (accumulator). A small accumulator vessel prevents the pump from short-cycling every time a tap drips. This extends motor life significantly.
  • Dry-run protection. The pump should cut out automatically if the tank runs empty, rather than burning out.

As a Johannesburg reference point, borehole pumps typically cost R15,000–R35,000 installed; a simpler backup-tank pressure pump is generally less, but confirm actual costs with installers because pump sizing, pipe runs and electrical work vary widely.

If you are weighing up gravity versus pressurised flow in more detail, the article on gravity vs pressurised backup water covers the trade-offs thoroughly.

Upgrade 2: Adding a second tank for more storage

Once you have pressure, storage becomes the next constraint. A single 2,500-litre tank provides a rough guide of about 10 days of drinking and cooking water for a family of four — far less if you are running showers and laundry from it. Adding a second tank in series (or parallel, depending on your site) doubles your buffer without doubling complexity.

Key considerations:

  • Tanks connected in series fill sequentially; tanks in parallel fill simultaneously and share load. Your installer will advise which suits your inlet pressure and space.
  • Confirm that the existing stand or base can carry the additional weight. A full 5,000-litre tank weighs five tonnes.
  • If you plan to add rainwater harvesting later, the inlet plumbing should be designed for it now to avoid rework.

As a rough guide, complete backup tank-and-pump systems in Johannesburg typically run R20,000–R40,000, with whole-house setups around R55,000. Adding a second tank to an existing system is a subset of that range, but get quotes for your specific configuration.

If your current setup needs a pump, a bigger tank, or an automatic switchover, a site-specific quote will tell you exactly what works for your pipes and pressure. Compare 3 free quotes — vetted installers, no obligation.

Upgrade 3: Automatic municipal-to-tank switchover

A manual switchover valve requires you to notice the outage, walk to the tank, and turn a lever — then remember to switch back. An automatic switchover uses a pressure sensor or float-operated valve to shift supply from the municipal line to your tank when municipal pressure drops, then revert when it returns.

This upgrade matters most for households where outages happen without warning, or where nobody is home during the day. It also protects against the tank accidentally emptying if municipal supply is restored while the inlet is still on tank-side.

The municipal-to-tank switchover guide explains the valve types, installation positions and backflow-prevention requirements in more detail — worth reading before you specify parts.

One point that often catches homeowners out: some municipalities require a registered plumber to install or modify the connection between the municipal line and any storage vessel. Check your local by-laws before proceeding, as this affects both insurance and compliance.

Upgrade 4: Connecting to a borehole

If your property has access to groundwater, connecting an existing backup tank to a borehole is a logical evolution — the tank becomes a header vessel that the borehole pump fills, reducing your dependence on both municipal supply and rainfall. This upgrade typically involves a borehole pump, rising main, surface controller, and replumbing the tank inlet.

Complete borehole systems in Johannesburg typically run R40,000–R150,000, with most falling between R60,000 and R100,000, depending on depth, yield and pump specification. The article on upgrading from a backup tank to a borehole covers when this step makes financial sense and what the drilling and equipping process involves.

Water quality is a separate consideration. Any borehole water used indoors should be tested against SANS 241 (2024 edition), the South African drinking-water quality standard, before it enters your household supply. Treatment may or may not be required depending on what the test shows.

Ready to take your system to the next level, whether that's a borehole connection or just a decent pump? Get matched with up to three installers — no cost, no commitment.

Sequencing your upgrades: a practical order

If you are building up from a basic tank and want to prioritise, here is a sensible sequence for most households:

PriorityUpgradeMain benefit
1Pressure pump with auto-startUsable water pressure throughout the house
2Automatic switchover valveOutages handled without manual intervention
3Second tankLonger buffer during extended outages
4Rainwater inlet or borehole connectionReduces reliance on municipal fill

This order is a rough guide, not a rule. If your tank is already elevated and gravity pressure is acceptable, the switchover valve may be more urgent than the pump. An installer who has seen your setup will give better advice than any generic sequence.

The single most useful thing you can do before spending anything is to have one or two installers walk through your existing system. Most will assess it as part of quoting, at no charge. That conversation will tell you whether your planned upgrade is straightforward, whether your tank position or pipe sizing limits your options, and what the job will realistically cost.

Quick answers

Can I add a pressure pump to any existing backup tank?

In most cases yes, but the tank position, pipe diameter and nearby electrical supply all affect whether the installation is straightforward. A ground-level tank with undersized pipes may need replumbing before the pump performs correctly. Have an installer assess your setup before purchasing a pump, as sizing matters — an oversized pump on a small tank can short-cycle and wear out quickly.

Will adding a second tank require a plumber or can I do it myself?

Connecting a second tank to an existing municipal inlet, or to a pump system, typically involves plumbing work that should be done by a registered plumber — particularly where the connection touches the municipal supply line. DIY tank connections can void product warranties and may create compliance issues with insurers. At minimum, have the final connection and overflow checked by a professional.

What is an automatic switchover valve and do I really need one?

An automatic switchover valve detects when municipal pressure drops and shifts your household supply to the backup tank without any action from you, then reverts when municipal pressure returns. If outages are infrequent and someone is usually home, a manual valve may be sufficient. If outages happen without warning or the property is often unoccupied, automatic switchover is worth the extra cost for the convenience and protection it provides.

How do I know if my existing tank is big enough before adding a pump?

South Africans use on average about 237 litres per person per day according to IWA Water Policy figures, though indoor-only backup use is typically less. As a rough guide, multiply the number of people in your household by your expected daily backup consumption and check how many days your tank volume covers. If your outages regularly exceed your tank's supply, adding a pump before adding storage may leave you with pressure but no water — size the tank first.

Does adding a borehole connection to my existing tank require water quality testing?

Yes. Any borehole water used for drinking or cooking should be tested against SANS 241 (2024 edition), the South African drinking-water quality standard, before it enters your household supply. The test results determine whether treatment — such as UV sterilisation or filtration — is needed. Skipping testing and later discovering contamination is a significantly more expensive problem than the test itself.

Sources & notes

Pricing reflects typical Johannesburg market ranges and is confirmed by installer quotation. References: SABS

Ready to compare? Get up to 3 quotes from vetted backup water systems installers in Johannesburg — free, no obligation.

Get 3 free quotes

Stop hoping the taps work.

Get your 3 free quotes today.

Get 3 free quotes