How it works

Water Tank Float Switches: How They Control and Protect Your Pump

By the WaterQuotes team · Published 2026-11-09 · 7 min read

Flat illustration showing a cross-section of a water tank with a float switch wired to a pump controller, indicating high and low water level positions

If your backup pump runs dry and burns out, or your tank overflows at two in the morning, there is a reasonable chance a float switch was either missing or wired incorrectly. Float switches are small, inexpensive, and genuinely important — yet they are regularly confused with float valves, skipped entirely, or installed the wrong way around. This article explains what a water tank float switch actually does, how to use one correctly, and what to watch out for before your installer finishes the job.

Float Switch vs Float Valve: Get This Right First

The two terms sound similar and both live inside or on a water tank, so the confusion is understandable — but they do completely different jobs.

A float valve (sometimes called a ball valve or ballcock) is a purely mechanical device. It opens and closes to control the flow of water into the tank, using a floating ball or arm to sense the water level. When the tank is full, the arm rises and shuts the inlet. No electricity involved. If you want to understand how these behave when things go wrong, the water tank overflowing guide covers the failure modes in detail, and water tank float valves explains how to service or replace them.

A float switch, by contrast, is an electrical switch. It does not control water flow — it controls power to a pump (or a pump controller). Inside the switch is a reed contact or a simple tilt mechanism: as the water level rises or falls past the switch’s position, it either opens or closes the electrical circuit. That signal is used to start or stop a motor.

Using one where you need the other will not work. Using neither leaves your pump vulnerable.

What a Float Switch Actually Does for Your Pump

A backup water pump — whether it feeds your house from a JoJo tank, a rainwater harvesting tank, or a storage tank connected to a borehole — faces two main risks:

  1. Dry running. If the pump draws water when the tank is empty, it overheats within minutes. Most pumps are not self-protecting; they will burn out.
  2. Unnecessary cycling. A pump that starts and stops too frequently wears out faster and can cause pressure spikes.

A correctly installed float switch solves the first problem outright. A low-level float switch sits near the bottom of the tank. When water drops to that point, the switch opens the circuit and cuts power to the pump before air can enter the inlet. The pump simply stops. No water, no damage.

A high-level float switch near the top of the tank does the opposite: once the tank is full, it can cut power to a fill pump or trigger an alarm, preventing overflow.

Many installations use two switches in combination — one to start the pump when the level is acceptable, one to stop it at low level — giving the pump a defined operating window. If you are deciding whether your tank setup even needs a pump, the article do you need a pump for a water tank is a useful starting point.

Types of Float Switch Used in South African Tank Installations

There is no single standard type, so knowing the options helps when you are discussing a new installation with a contractor or troubleshooting an existing one.

TypeHow it worksTypical use
Tilt / hanging floatA weighted ball inside a cable-hung float tilts as level changes, opening or closing internal contactsVery common in JoJo and similar poly tanks
Vertical float (stem-mounted)A float rides up and down a fixed stem, triggering a reed switch at set pointsUseful where tank geometry is awkward
Electronic level sensorNo moving parts; uses conductivity or ultrasonic measurementMore reliable long-term, higher upfront cost
Pressure-based switchReads hydrostatic pressure at the tank baseOften used in larger agricultural or commercial tanks

For most South African residential backup water systems, a hanging tilt-type float switch is what you will encounter. It is cheap, easy to replace, and works reliably in polyethylene tanks — provided it is wired and positioned correctly.

Wiring Mistakes That Cause Real Damage

A float switch is a simple device, but simple devices are still wired incorrectly with surprising regularity. The most common mistakes:

Wrong mode (normally open vs normally closed). A switch can be wired as normally open (NO — circuit completes when float rises) or normally closed (NC — circuit breaks when float rises). Using the wrong mode reverses the logic entirely: your pump runs dry when it should stop, and refuses to start when it should run. Always confirm with the installer which mode is configured and test it before sign-off.

Low-level switch positioned too high. If the cut-off point is set too far up the tank, you lose usable storage. Set too low, the pump may draw air before the switch trips. A good installer positions the low-level switch so it cuts out with enough water above the inlet to keep the pump primed.

No switch at all. Some installations rely on the homeowner manually monitoring tank levels. This is not a plan — it is a shortcut that eventually costs a pump replacement.

Direct wiring without a controller. A float switch should rarely be wired directly into a mains circuit without a relay or pump controller in between. The switch contacts are not always rated for the pump’s starting current, and a controller adds time-delay logic to prevent rapid cycling.

If your current backup system has no float switch or you are not sure how it is wired, it is worth getting a professional assessment. Compare 3 free quotes — vetted installers, no obligation.

Choosing a Float Switch for a JoJo or Poly Tank

The phrase “float switch for JoJo tank” comes up often because JoJo tanks are the dominant residential storage product in South Africa. The good news is that most standard tilt-type float switches fit without modification — the cable passes through the tank’s inlet or a small grommet hole, and the float hangs freely inside.

What to check before buying or specifying one:

  • Voltage and current rating. Match the switch to your pump controller’s input, not directly to the pump motor. Most residential controllers use a low-voltage signal input (12 V or 24 V DC) rather than mains switching.
  • Cable length. Measure the internal tank depth and add enough length to reach your controller box. Running short and splicing inside a wet tank is a problem waiting to happen.
  • IP rating. The switch body will be in a wet environment. IP68 is ideal; IP67 is acceptable for most tanks. Anything lower is a risk.
  • Replacement availability. Generic tilt-type switches are widely stocked by irrigation and pump suppliers nationally. Proprietary designs tied to a specific controller brand can become difficult to source.

How Float Switches Fit Into a Backup Water System

A float switch is one component in a broader setup. In a properly designed backup water system, the float switch connects to a pump controller or pressure switch, which manages the pump motor. The controller handles starting currents, time delays, and often provides a dry-run alarm output — a feature that works in addition to the float switch cut-off, not instead of it.

If your system feeds the house under pressure, a pressure tank (accumulator) will also be part of the picture, reducing how often the pump cycles. The float switch protects against empty-tank conditions; the pressure tank protects against short-cycling. Neither replaces the other.

For typical complete backup tank-and-pump setups in Johannesburg, costs generally run R20,000–R40,000 for smaller residential installations, with whole-house examples around R55,000 — but these are Johannesburg reference points and actual pricing varies considerably by region, tank size, and site complexity. Always confirm figures through installer quotes.

Float switches, controllers, pressure tanks — getting the components to work together properly is where installer experience matters most. Get quotes from up to three vetted installers and compare their approach before committing.

Maintenance: What to Check and When

Float switches require very little routine attention, but they do fail — usually because the float body cracks, the cable insulation degrades in UV, or the internal contacts corrode over years of damp exposure. A few habits will catch problems before they become a burned-out pump:

  • Test the switch manually every six months. Lift the float by hand with the pump running and confirm the pump stops. Lower it and confirm it starts. This takes under a minute.
  • Inspect the cable entry point where it passes through the tank wall or lid. UV exposure and mechanical stress at this point are the most common failure locations.
  • Check after any major pump service. If a technician disconnects and reconnects the control wiring, verify the switch logic has not been inadvertently reversed before returning the system to service.
  • Replace proactively after five to seven years. A float switch costs a fraction of a pump. If your system is ageing, changing the switch on a schedule is cheap insurance.

A working float switch is not glamorous. It sits in the dark at the bottom of your tank and does nothing most of the time. But on the day your tank runs unexpectedly low, it is the component standing between normal operation and an expensive pump replacement.

Quick answers

What is the difference between a float switch and a float valve?

A float valve is a mechanical device that controls water flow into a tank — it uses a floating arm to open and close an inlet, with no electrical connection. A float switch is an electrical sensor that opens or closes a circuit to start or stop a pump motor. They serve completely different purposes and one cannot substitute for the other.

Where should a low-level float switch be positioned inside a water tank?

The low-level switch should be positioned so that it cuts power to the pump while there is still enough water above the pump inlet to keep it primed — typically 150 mm to 300 mm above the inlet, depending on tank geometry and pump type. Set too low, the pump may draw air before the switch trips; set too high, you lose usable storage capacity. Your installer should confirm the position based on your specific tank and pump combination.

Can I wire a float switch directly to my pump without a controller?

It is generally not recommended. The internal contacts of a typical residential float switch are rated for low currents, and directly switching a pump motor — with its high starting surge — risks burning out the switch contacts. A pump controller or relay in between protects the switch and also adds useful features like time-delay logic to prevent rapid cycling.

My pump keeps running even when the tank is nearly empty — could the float switch be faulty?

Yes, that is one of the most common float switch failure symptoms. The switch contacts may have welded closed, the float body may have cracked and filled with water (preventing it from floating), or the switch may have been wired in the wrong mode (normally open vs normally closed). Test the switch manually by lifting the float and checking whether the pump stops; if it does not, the switch or its wiring needs attention.

Do float switches work with all types of water tanks, including JoJo tanks?

Standard tilt-type hanging float switches are compatible with most polyethylene tanks used in South Africa, including common JoJo models. The cable typically passes through an inlet fitting or a grommet hole in the lid. Check that the switch has an adequate IP rating for a wet environment (IP67 or IP68) and that the cable length suits your tank's depth before purchasing.

Sources & notes

Pricing reflects typical Johannesburg market ranges and is confirmed by installer quotation. References: SABS

Ready to compare? Get up to 3 quotes from vetted backup water systems installers in Johannesburg — free, no obligation.

Get 3 free quotes

Stop hoping the taps work.

Get your 3 free quotes today.

Get 3 free quotes