How it works

Water Tank Not Refilling After an Outage: Float Valves, Airlocks and Low Inlet Pressure

By the WaterQuotes team · Published 2026-11-11 · 7 min read

Flat illustration of a household water tank with a float valve, inlet pipe and pressure gauge, showing a troubleshooting checklist

The municipal supply has come back on, the taps in the kitchen are running again, and yet the tank sits stubbornly at the same low level it was at during the outage. It is a frustrating situation, but it is also an extremely common one — and in most cases the fix requires nothing more than a screwdriver, a pair of pliers and about twenty minutes.

This guide walks through every likely cause, in the order you should check them, so you can get your backup supply back up and running without calling anyone out unnecessarily.

Why tanks often fail to refill immediately after supply returns

When municipal pressure drops to zero — or close to it — a few things can go wrong inside and around your tank’s inlet system simultaneously. The float valve may lock in the closed position after being rattled by pressure surges. Air that entered the pipework while the main was dry can sit in the inlet line and block water from reaching the valve. The strainer at the inlet may have caught debris that was flushed through when the main was first repressurised. And even when supply is technically back, low residual pressure may not be enough to lift water to the tank, particularly if you live in a high-lying suburb.

Understanding this is a system of linked parts — not just a single component — is the key to diagnosing it quickly.

Start here: check actual mains pressure at the inlet

Before touching the float valve or anything inside the tank, confirm that pressure at your street connection has genuinely recovered. Open a garden tap or a low-lying indoor tap and watch the flow. A trickle rather than a full stream usually means the network is still recovering pressure.

Residents in elevated suburbs are more exposed here. As covered in the guide to high-lying suburbs and water pressure, homes at the top of a reticulation zone routinely receive the lowest residual pressure, and after a lengthy outage they are often the last properties to see adequate flow. If you are in one of these areas, waiting another hour before troubleshooting further is often the most practical first step.

If pressure at a low-lying tap looks normal, the issue is local to your tank system. Move on.

Float valve problems: stuck, waterlogged or mechanically jammed

The float valve is the single most common culprit. Its job is simple: when the water level drops, the float drops, the valve opens, water enters. When the tank is full, the float rises and closes the valve. After an outage, two things can go wrong.

Stuck in the closed position. A pressure surge when supply returned may have forced the valve hard against its seat, where surface tension or a worn rubber washer now holds it shut even though the float is low. Manually push the float arm downward with your hand. If water immediately starts flowing in, you have confirmed this is the problem. Often the valve will continue working normally after this manual reset. If it sticks repeatedly, the washer needs replacing — a part that typically costs well under R100 and takes ten minutes to swap out.

Waterlogged float. On older ball-and-arm type valves the plastic or metal float can develop a small crack and take on water, making it too heavy to rise properly and triggering the valve to stay open — or in some cases the float sits so low permanently that the valve never opens fully. Remove the float, shake it next to your ear, and feel for extra weight. A waterlogged float needs replacing. Consult our detailed piece on water tank float valves for a full breakdown of valve types, failure modes and when to replace versus repair.

Airlocks in the inlet pipe

When a pipe runs dry during an outage, air fills the void. When pressure returns, water rushes in from below, but a pocket of air trapped at a high point in the pipe can hold its position, blocking water from reaching the valve. This is called an airlock.

You may hear gurgling or intermittent burping from the inlet line — both signs that air is being partially displaced but not fully cleared. The simplest fix is to open any bleed point on the inlet pipe and allow the trapped air to escape. If there is no accessible bleed point, temporarily loosening a compression fitting just enough to hear air hiss out — then immediately retightening it — usually clears the blockage. Where the inlet pipe has been plumbed with long horizontal runs or unexpected high points, airlocks are more likely to recur and replumbing that section at a slight continuous fall toward the tank is the lasting solution.

Clogged inlet strainer or ball valve left closed

Most properly installed tank systems include a strainer or filter just before the float valve to catch grit and debris. When a dry main refills, it carries loosened sediment, pipe scale and sometimes fine sand through the network. That debris concentrates on your strainer.

Shut off the inlet isolation valve, remove the strainer body, rinse the mesh under a tap, and reinstall. This takes about five minutes and is worth doing as routine maintenance after every significant outage regardless of whether you are having refilling problems.

While you are at it, confirm that the isolation ball valve immediately before the tank inlet is fully open. It sounds obvious, but after any maintenance or during an emergency, valves are sometimes left partially closed and forgotten.

If the fault turns out to be more than a quick fix, a vetted installer can assess your whole inlet setup. Get 3 free quotes — no obligation, no sales calls.

There is a related scenario that is easy to mistake for a refilling problem: the tank does slowly refill, but then immediately starts wasting water through the overflow pipe. This usually means the float valve is not closing properly at the full level — a failed washer, a bent float arm, or a waterlogged float that can no longer rise high enough to shut off flow. The result is a tank that cycles water continuously and may actually overflow while appearing only half full from certain angles. If you notice water running from your overflow outlet, the article on a water tank overflowing covers exactly this failure mode and how to correct it.

When the problem is the broader backup system design

Sometimes working through each of the above steps confirms that everything is mechanically sound — and yet the tank still refills very slowly or incompletely. In that case the limiting factor is likely the design of the system itself: undersized inlet pipework, a float valve orifice too small for the pressure available, or a tank positioned at an elevation that the available municipal pressure can barely reach.

This is a good moment to review your whole setup. A properly designed backup water system accounts for local pressure conditions, the height of the tank relative to the street main, and realistic refill times based on household daily consumption. If your installer sized components for normal pressure and your area routinely sees low pressure, the system will consistently underperform.

For context on costs if you are considering upgrading or adding a booster pump to assist refilling, backup tank-and-pump systems in Johannesburg typically run R20,000–R40,000, with whole-house setups around R55,000. Treat these as reference points only — confirm current pricing via quotes, as costs vary by location, tank size and site conditions.

Thinking about upgrading your backup setup to handle future outages better? Compare quotes from 3 vetted installers — straightforward, no obligation.

A quick diagnostic checklist

CheckWhat to look forTypical fix
Mains pressureWeak flow at a low-lying tapWait; call municipality if prolonged
Float valveArm not dropping freely, float heavyManual reset; replace washer or float
AirlockGurgling in inlet pipe, intermittent flowBleed air at highest accessible point
Inlet strainerVisible debris, restricted flowRemove, rinse, reinstall
Isolation valvePartially closedOpen fully
Overflow outletWater running when tank not fullAdjust or replace float valve

Working through this list in order will resolve the vast majority of post-outage refilling problems without any specialist help. When it does not, you have at least gathered useful diagnostic information to give a plumber or water installer — which makes the callout shorter and cheaper.

Quick answers

How long should a tank normally take to refill after the supply comes back?

Refill time depends on your tank size, the inlet pipe diameter, and the municipal pressure available at your property. As a rough guide, a 2,500-litre tank on a standard 15 mm inlet at normal suburban pressure might take two to four hours to refill fully. If your tank is still low after six hours and pressure elsewhere in the house seems normal, work through the float valve and airlock checks in this article.

Can low municipal pressure alone prevent a tank from filling?

Yes. If the pressure is insufficient to push water up to the height of your tank's inlet — particularly relevant in high-lying areas — the tank will fill very slowly or not at all even when the supply is technically restored. A pressure-boosting pump on the inlet can solve this, but confirm the pressure issue first with a simple gauge reading before spending money on equipment.

My float valve was replaced recently. Why is it sticking already?

A new float valve can still stick if the replacement washer material is not compatible with the local water chemistry, if the valve seat has accumulated scale, or if water hammer during pressure surges is forcing the valve hard against its seat repeatedly. Fitting a water hammer arrestor on the inlet line and descaling the valve seat usually resolves persistent sticking.

Is it safe to drink water from the tank after an outage?

South African drinking water must meet SANS 241 (2024 edition) at the point of supply, but that standard applies to the municipal network, not necessarily to what has been sitting in your storage tank. After a prolonged outage, flush the tank before use if you can, and if you use the water for drinking, consider testing it or running it through a certified point-of-use filter as a precaution.

Should I install a booster pump to help the tank refill faster?

A booster pump on the municipal inlet can meaningfully improve refill times if your pressure is consistently low, but it must be installed in compliance with your municipality's bylaws — most prohibit connecting a pump directly to the street main without an approved break tank arrangement. Get a qualified installer to assess your site before purchasing any equipment, as the wrong setup can damage the pump or create backflow risk into the network.

Sources & notes

Pricing reflects typical Johannesburg market ranges and is confirmed by installer quotation. References: SABS

Ready to compare? Get up to 3 quotes from vetted backup water systems installers in Johannesburg — free, no obligation.

Get 3 free quotes

Stop hoping the taps work.

Get your 3 free quotes today.

Get 3 free quotes