How it works

Table View, Milnerton and Melkbosstrand Boreholes: Sand, Salt and Yield

By the WaterQuotes team · Published 2026-11-12 · 6 min read

Flat illustration of a coastal borehole cross-section showing sandy layers, a casing pipe and the sea nearby

Drilling for groundwater along Cape Town’s West Coast is not the same exercise as drilling in the Cape Winelands or on the Highveld. The Atlantic seaboard geology — shallow sand over variable rock, a water table that sits close to the surface and the constant nearness of the ocean — introduces complications that catch out homeowners who treat a borehole as a plug-and-play upgrade. This article walks through the geology, the risks and the practical decisions you will face if you are considering a west coast borehole in Table View, Milnerton or Melkbosstrand.

What the ground looks like here

The West Coast strip from Milnerton to Melkbosstrand sits on coastal plain deposits: wind-blown sand dunes, sandy alluvium and, at depth, the Malmesbury Group shales and phyllites that underlie much of the Cape Peninsula’s northern suburbs. What this means in practice is that the top section of any borehole — sometimes as much as 20–40 m depending on location — is unconsolidated or semi-consolidated sand before the drill hits fractured rock.

That sandy overburden is where most of the headaches start. Without correct casing and screen sizing, fine sand migrates into the borehole, damages the pump impellers and silts up the system. If you have already noticed gritty particles coming through your tap, the guide on sand in borehole water explains what is happening and what can realistically be done about it.

Saltwater intrusion: the coastal risk you must take seriously

Fresh groundwater along the West Coast sits in a delicate balance with saline water beneath and, in lower-lying areas, laterally from the sea. This is a standard coastal hydrogeology problem: pump too hard, too often, or from the wrong depth, and you draw saline water into your freshwater zone. Once saltwater intrusion happens at a borehole, it is very difficult to reverse.

The practical implication is that pump yield — the rate at which water is drawn from the aquifer — needs to be matched carefully to what the aquifer can sustainably supply. A driller experienced in this coastal strip should conduct a proper yield test rather than simply setting the pump at maximum output. Over-abstraction is the most common cause of salinity problems in this area, and it is an entirely avoidable one if the pump is correctly specified from the outset.

That said, some natural salinity exists in coastal aquifers regardless of pumping rate. This is why water testing is not optional here — it is the only way to know what you are actually working with before and after installation.

Casing: getting the specification right for sandy conditions

In hard-rock areas, casing is primarily needed to line the unstable top section and keep the borehole open. In sandy coastal terrain, it carries an additional function: keeping the formation out of the water column. The casing diameter, material, slot size of any screens and the gravel-pack design around the screen all need to reflect the grain size of the local sand.

Specifying the wrong screen slot size is surprisingly common and leads directly to the sand-in-water problems mentioned above. If you want to understand what your installer should be specifying and why, the article on borehole casing explained breaks down the components in plain terms so you can have an informed conversation with any driller quoting you.

Yield expectations: what is realistic on the West Coast

Yield varies significantly across even a small geographic area, depending on whether a borehole intercepts fractured rock or stays within the sandy overburden. As a rough guide, boreholes that reach the Malmesbury shale fracture zones tend to produce more consistent yields than those relying entirely on the sand aquifer, which is seasonally variable and affected by rainfall recharge.

Expecting a driller to guarantee a specific yield before drilling is unreasonable — no reputable operator can do that honestly. What you should expect is a yield test after the borehole is complete, documented results, and a pump recommendation based on those results rather than on the pump the installer happens to have in stock.

For Johannesburg context, complete borehole systems typically run R60,000–R100,000 for most installations, with the full range being R40,000–R150,000 depending on depth and specification. Treat these as a Johannesburg reference point only — West Coast pricing will differ, so confirm everything via local quotes.

Coastal boreholes need drillers who know the local geology — not generalists. Get three free quotes from vetted installers — no obligation, no sales calls unless you want them.

Water testing: what to test and why SANS 241 matters

SANS 241 (2024 edition) is the South African drinking-water quality standard that sets limits for a wide range of parameters including microbial contamination, nitrates, pH and — critically for coastal areas — electrical conductivity and chloride levels. A basic water test ordered through many drillers checks only a handful of parameters and may not flag borderline salinity.

For a coastal borehole, you should ask specifically for a test that includes chloride, electrical conductivity (as a salinity proxy), sodium, hardness and total dissolved solids, in addition to standard microbial screening. If the borehole is near any agricultural land or on a plot with a septic system, nitrate testing matters too.

The article on borehole water testing costs explains the different testing tiers, what each one covers and what laboratory accreditation to look for. Getting this wrong is not a theoretical risk — in coastal sandy aquifers, water chemistry can shift over time as the aquifer responds to pumping and seasonal recharge.

Treatment options if salt or hardness is elevated

If your water test returns elevated chlorides or conductivity, the main treatment routes are reverse osmosis (for point-of-use drinking water) or, for whole-house use, a more involved reverse osmosis or nanofiltration system. Neither is cheap to run, and both produce a concentrate waste stream that needs to be managed.

The honest position: if initial testing shows significant saltwater intrusion, the most cost-effective decision may be to use the borehole for irrigation only and to source drinking water from the municipal supply, treating the borehole as a supplement rather than a replacement. That is a less exciting outcome than a full household solution, but it is the realistic one for some coastal sites.

If you are weighing up whether a borehole makes financial sense for your site, talking to installers with local experience is the fastest way to get a straight answer. Compare quotes from three West Coast installers — free, with no obligation to proceed.

Choosing an installer who knows the West Coast

The variables on the West Coast — sand management, salinity risk, yield testing, casing specification — mean that an installer’s local track record matters more than their general reputation. When you are evaluating quotes, ask specifically about previous boreholes in Table View, Milnerton or Melkbosstrand, what yields those produced and what water quality looked like on a fresh test. A driller who cannot give you any local reference point is not necessarily unqualified, but it is worth understanding why.

Also confirm that the installer will conduct a proper yield test after drilling and provide written results, that their casing and screen specification is based on a site-specific assessment, and that they carry the required drilling registration under South African water legislation. WaterQuotes matches homeowners with up to three vetted installers so you can compare these answers side by side before committing to anything.

Quick answers

Is it possible to get drinkable water from a borehole in Table View or Milnerton?

Yes, but it depends on the specific site and what the water test shows. Some boreholes in the area produce water that meets SANS 241 standards with minimal treatment; others have elevated salinity or hardness that requires a treatment system. Testing after drilling is the only way to know for certain what you are working with.

How do I know if my coastal borehole is experiencing saltwater intrusion?

The clearest indicators are a noticeable increase in water saltiness over time, water that tastes different from when the borehole was first commissioned, or a water test showing rising chloride or electrical conductivity readings. Having a baseline test done immediately after installation gives you a reference point to compare against later tests.

Why does sand keep appearing in my borehole water on the West Coast?

Sandy formation material enters the water column when the borehole screen slot size does not match the grain size of the surrounding sand, or when the gravel pack around the screen has not been correctly installed. Over-pumping — drawing water faster than the aquifer can supply — also accelerates sand migration. The fix usually involves assessing the casing and screen specification and sometimes reducing the pump rate.

What is a yield test and do I really need one?

A yield test measures how much water the borehole can sustainably produce over a given period, usually by pumping at a set rate and monitoring water levels. In coastal sandy aquifers where over-pumping directly increases salinity risk, the yield test result should determine your pump rate — not the other way around. It is not optional if you want the borehole to remain viable over time.

How much does a borehole typically cost in the Table View and Milnerton area?

Pricing along the West Coast will differ from Johannesburg benchmarks, so local quotes are essential. As a Johannesburg reference point, complete borehole systems typically run between R60,000 and R100,000 for most installations, with the full range from R40,000 to R150,000 depending on depth and specification. Get at least two or three detailed quotes from installers with West Coast experience before budgeting.

Sources & notes

Pricing reflects typical Johannesburg market ranges and is confirmed by installer quotation. References: City of Cape Town · Water Research Commission

Ready to compare? Get up to 3 quotes from vetted borehole drilling installers in Johannesburg — free, no obligation.

Get 3 free quotes

Stop hoping the taps work.

Get your 3 free quotes today.

Get 3 free quotes